Home  > FUJITSU(UNITARY)(x)
|◀ 13 - 19 of 19 ▶|
View:
  • CABINETUnit cabinet should be constructed of galvanized, pre-painted steel.
  • MOTORInherently protected motors are mounted inside of insulated cabinet to reduce motor noise. A choice of motor horsepowers and drive combinations are available to allow you to meet specified CFM at various static pressures up to 2" [.498 kPa] external static pressure.
  • LOW PROFILEAllows for horizontal installation in most standard drop ceiling applications, and the movement of units through most standard doorways for addition or replacement work.
  • THERMAL EXPANSION VALVESStandard all models.
  • FILTERSOne inch [25 mm] throwaway filters are standard, but filter racks are designed to accept either one inch [25 mm] or two inch [51 mm] filters.
  • EVAPORATOR COILTwo circuit, interlaced row split coils are constructed with copper tubes and aluminum fins mechanically bonded to the tubes for maximum heat transfer capabilities. All coil assemblies are leak tested up to 450 PSIG [3100 kPa] internal pressure prior to installation into units.
  • REFRIGERANT CONNECTIONSField piping connections are made through a fixed post between two side access panels on either side of the unit. Allows flexibility to meet most field conditions as well as full accessibility after the installation is complete. Units may be used with two straight cool condens ing units or single circuit manifolded in the field using the copper fittings shipped with each unit. The RHGN Air Handler has not been tested, rated or certified to operate with dual residential remote heat pumps.
  • DRAIN PANThe galvanized steel drain pan is designed to trap condensate in either vertical or horizontal installations. Condensate drain connections are located on both sides of the unit allowing complete flexibility to meet most field conditions.
  • SERVICE ACCESSTwo removable panels on top and each side of the unit are easily removed for access to motors, blowers, sheaves, and filters.
  • HORIZONTAL OR VERTICALAll models are designed for either application and can be installed in either position as supplied from the factory.
  • TESTINGAll units are run tested at the factory prior to shipment. Units are shipped with a holding charge of nitrogen.

  • Item#:
    RHGL-240ZK
    Manufacturer Item:
    RHGL-240ZK
    Manufacturer:
    FUJITSU(UNITARY)
    Rheem A/C RSPMA036JK000 Packaged Air Conditioner Dedicated Horizonta 3 Ton 208/230/1 14 SEER
    • Name Rheem RSPM-A036JK000 - Classic 3 Ton, 14 SEER, Packaged Air Conditioner - Dedicated Horizontal, 208-230 V, 1 Ph, 60 Hz
    • Weight 333lbs
    • Length 59.9"
    • Width 34.0"
    • Height 33.5"
    • SEER 14
    • EER 12.2
    • Refrigerant R-410A
    • CFM 3,400
    • Cooling Capacity 36,000 BTU
    • Air Flow Horizontal
    • Voltage 208/230 VAC
    • Phase Single
    • Minimum Circuit Amps 22.6
    • Maximum Fuse Size 40
    • Blower Motor HP 1/2 HP
    • Condenser Motor HP 1/3 HP
    • Drive Type Direct Drive
    • Energy Star Rated Yes,
      ,

    Item#:
    RSPMA036JK000
    Manufacturer Item:
    RSPM-A036JK000
    Manufacturer:
    FUJITSU(UNITARY)
    Fujitsu FH6021TTSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
    The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections
    Item#:
    FH6021TTSJSN
    Manufacturer Item:
    FH6021TTSJSN
    Manufacturer:
    FUJITSU(UNITARY)
    Features

  • Fujitsu Indoor Furnace cased coils and replacement uncased coils are designed for use with Fujitsu outdoor units and are available for vertical upflow or downflow, and horizontal left or horizontal right airflow. When matched with Fujitsu outdoor units, the coils provide a nominal capacity range from 18,000 /HR [5.24 kW] to 60,000 /HR [17.6 kW].
  • Constructed of aluminum fins bonded to internally grooved aluminum tubing.
  • Coils are tested at the factory with an extensive refrigerant leak check.
  • Coils have copper sweat refrigerant connections.
  • Feature two sets of 3/4" [14.1 mm] N.P.T. Condensate
    drain connections for ease of connection.
  • Chatleff metering device connections, at inlet and outlet of TXV or EEV and equalizer connections (TXV only).
  • Approved for system application with variety of Fujitsu outdoor units.
  • Condensate drain pan is constructed of high grade, heat resistant, corrosion free thermal-set material.
  • Compatible with Germicidal Light System (UV resistant)
  • Bi-Directional airflow eliminates the need to switch any internal components from horizontal left to right.
  • Unique drain pan design maximizes application flexibility and condensate removal.
  • N-Coil design maximizes performance and minimizes height required at installation.
  • Coils are AHRI certified for system application with a variety of Fujitsu outdoor units
  • Item#:
    FCCN3621SZTA
    Manufacturer Item:
    FCCN3621SZTA
    Manufacturer:
    FUJITSU(UNITARY)
  • Features
  • Up to 96% residential gas furnace CSA certified
  • 4 way multi-poise design
  • Two stages of operation to save energy and maintain optimal comfort level.
  • Diagnostics 7-Segment LED all units
  • Ignition System  DSI for reliability and longevity
  • Water Management System with patented Blocked Drain Sensor
  • Heat exchanger is removable for improved serviceability. Aluminized steel primary and stainless steel secondary construction provide maximum corrosion resistance and thermal fatigue reliability.
  • Low profile 34 inch cabinet ideal for space constrained installations.
  • Blower Shelf design  serviceable in all furnace orientations
  • Pre marked hoses  insures proper system drainage
  • Vent with 2" or 3" PVC
  • Replaceable Collector box
  • Hemmed edges on cabinet and doors
  • Quarter turn fasteners for tool less access
  • Integrated control boards feature dip switches for easy system set up
  • Self priming condensate trap
  • Solid bottom included
  • Cabinet air leakage less than 2% at 1 inch H 2O when tested in accordance with ASHRAE standard 19
  • Item#:
    FF85215PT96M
    Manufacturer Item:
    FF85215PT96M
    Manufacturer:
    FUJITSU(UNITARY)

    Item#:
    RGEDZR090ACA202AAAA0
    Manufacturer Item:
    RGEDZR090ACA202AAAA0
    Manufacturer:
    FUJITSU(UNITARY)
    Fujitsu General heating and cooling offers parts that are perfectly designed and engineered to fit your A/C and Heating Unit right the first time and deliver year-round comfort.Fujitsu Parts 46-101944-02 Transformer 40 VA 120-24 VAC Foot Mount,
    ,

    Item#:
    46-101944-02
    Manufacturer Item:
    46-101944-02
    Manufacturer:
    FUJITSU(UNITARY)
    |◀ 13 - 19 of 19 ▶|
    View: