Watts AS-MB-100 Microbubble Air Separator, 1", IPS, 150 psig, 240 deg F, 15 gpm, Forged Brass, 3-12/16" L x 6-15/16" H

• Features a durable brass body construction, corrosion-resistant polyphenylsulfone coalescing media that withstands petroleum based cleaners, glycol anti-freeze
• Requires no minimum inlet/outlet piping length for proper operation
• DuoVent air vent assembly has a high-capacity and high-temperature rating
• Fully serviceable - can be disassembled for inspection and cleaning
• Bottom tapping for use with series RBFF residential boiler fill fitting

,
,

Watts Water AS-MB100

Amtrol Parts 420-6 Mixing Valve Repair Kit

Sid Harvey Item #:B48-46: Replaces Part #:'s : B48-46,
,

Amtrol Parts B48-46

Hoffman 401475 Steel Non-Vacuum Water Vent Valve, 1/8", NPT

• For automatic or manual venting systems
• Disc-type vent
• Built-in check valve
• Cartridge with discs can be replaced without draining the system
• 1/8" NPT straight shank
• Straight body styleSid Harvey Item #:401475: Replaces Part #:'s : 41009,
  ,
  
  

Watts Regulator series 53L pressure relief valves are used in residential applications to protect against excessive pressure on domestic storage tanks and tankless water heaters. It consists of a bronze body construction with NPT threaded male inlet and NPT threaded female (drain) outlet connections, stainless steel spring, and test lever.

• Used for protection against excessive pressure on domestic storage tanks or tankless water heaters
• Furnished with test levers
• Relieves excessive pressure on storage tanks and tankless water heaters
• Compatible with model 210 gas shutoff valves

,
,

Watts Regulator series 53L pressure relief valves are used in residential applications to protect against excessive pressure on domestic storage tanks and tankless water heaters.

• Used for protection against excessive pressure on domestic storage tanks or tankless water heaters
• Furnished with test levers
• Relieves excessive pressure on storage tanks and tankless water heaters
• Compatible with model 210 gas shutoff valves
• Stainless steel spring

Sid Harvey Item #:B145-22: Replaces Part #:'s : 2K411
,
,

Watts Water B145-22

Watts Regulator series 3L pressure relief valves are used in residential applications to protect against excessive pressure on domestic storage tanks, tankless water heaters, and solar heating applications. It consists of a bronze body construction with NPT threaded male inlet and NPT threaded female (drain) outlet connections, stainless steel spring, and test lever.

• Used for protection against excessive pressure on domestic storage tanks or tankless water heaters
• Popularly used in conjunction with the model 210 gas shutoff valve on gas water heaters to shut off gas to heater if water heater temperature exceeds 210 deg F
• Furnished with test levers
• Relieves excessive pressure on storage tanks and tankless water heaters
• Compatible with model 210 gas shutoff valves
• Stainless steel spring

,
,

Watts Water B145-23

Bell & Gossett B-38 Cast Brass Pressure Reducing Valve, 1/2", NPT, 10 - 25 psig

• Fast fill feature reduces start-up time and labor
• Low inlet pressure check valve help prevent loss of system pressure if the supply water drops below system pressure
• Convenient cleanable strainer is designed to prevent dirt and sediment from entering the system
• Brass body construction is highly resistant to corrosion-ideal for water systems
• Reducing valves protect heating and plumbing systems against excessive line pressures
• Equipped with built-in-strainer and low inlet pressure check valve
• They are factory set at specified limits although adjustment is easily made
• Construction - cast brass body, with special insert diaphragm, EPDM check valve, brass seat, brass with EPDM insert stem, brass valve plate, stainer and strainer nut wetted parts and steel non-wetted parts

Sid Harvey Item #:B138-8A: Replaces Part #:'s : B138-7R,
,

Bell & Gossett B7-12 Cast Brass Pressure Reducing Valve, 3/4", NPT, 10 - 25 psig

• Fast fill feature reduces start-up time and labor
• Low inlet pressure check valve help prevent loss of system pressure if the supply water drops below system pressure
• Convenient cleanable strainer is designed to prevent dirt and sediment from entering the system Brass body construction is highly resistant to corrosion-ideal for water systems
• Reducing valves protect heating and plumbing systems against excessive line pressures
• Equipped with built-in-strainer and low inlet pressure check valve
• They are factory set at specified limits although adjustment is easily made
• Construction - cast brass body, with special insert diaphragm, EPDM check valve, brass seat, brass with EPDM insert stem, brass valve plate, stainer and strainer nut wetted parts and steel non-wetted parts

Sid Harvey Item #:B138-10A: Replaces Part #:'s : B138-10R,
,

Bell & Gossett B138-10A

Resideo Braukmann DS06 Dial Set Pressure Regulating Valve is a high quality pressure regulating valve that maintains a constant outlet pressure over a wide range of inlet supply pressures. It is suitable for potable water and irrigation applications. The downstream pressure adjustment dial eliminates the need for a pressure gauge when adjusting the pressure setting (static pressure only).

• Built-In Dial-Set- no gauge is needed to install or set static pressure
• Built-in strainer to simplify maintenance
• Fabric reinforced diaphragm regulator, stainless steel and engineered thermoplastics internal parts
• Balanced single seat construction
• Minimum pressure differential between inlet and outlet ports is 14.5 psig
• Plus or minus 4 psig dial calibration
• Less than 0.25% of weighted average of low lead content
• 1/4" NPT gauge tap
• 10:1 maximum reduction ratio
• Double union sweat union fittings

,
,

Resideo Braukmann DS06-101-DUT-LF

Watts Regulators series B1156F bronze high capacity feed water pressure regulators are for use in commercial and residential hydronic heating systems to fill the boiler and piping system with water, and to maintain water pressure in the system at all times. It also provides make-up water to the system in the event of system leaks. It consists of a bronze body construction with NPT threaded inlet and outlet connections, a tight seating check valve, purge lever for manual purging, and a stainless steel strainer. Series B1156F has high capacity performance and simplified servicing design. It is suitable for use in the boiler feed lines of hydronic heating systems.

• Tight seating check valve
• Purge lever for manual purging
• High capacity performance as well as unique simplified servicing accessibility for complete unitized maintenance
• Stainless steel strainer to protect the valve disc from fouling
• Designed to fill the boiler and system piping with water and to maintain water pressure in the system at all times
• Provide make up water to the system in the event of system leaks
• 15 psi factory set, 100 psi maximum working pressure

,

,

Watts Water B1156F

Watts Regulators series 174A boiler pressure relief valves are used in hot water heating and domestic supply boiler applications to protect against excessive pressures on all types of hot water heating supply boiler equipment. It consists of a bronze body construction with NPT threaded female inlet and NPT threaded female outlet (drain) connections, non-metallic disc-to-metal seating, stainless steel spring, and test lever. Series 174A resists corrosive water conditions, sticking and freezing, and prevents water and sediment from being trapped in the seat. It is designed for emergency safety relief and shall not be used as an operating control.

• Safety relief valves for pressure protection only of all types of hot water heating boiler equipment
• Seat located above drain, water can't be trapped and sediment can't foul seat
• Non-mechanical seat-to-disc alignment will not stick or freeze
• Water seal of high temperature resisting material isolates spring working parts from water during relief

Sid Harvey Item #:B145-2: Replaces Part #:'s : 24572
,
,

Watts Regulators series 740 boiler pressure relief valves are used in hot water space heating boiler applications to protect against excessive pressure on all types of hot water space heating boiler equipment. It consists of a iron body construction with expanded outlet drain connections for hot water space heating boilers, non-metallic disc-to-metal seating, stainless steel spring, and test lever. Series 740 offers large discharge capacity, resists corrosive water conditions, resists sticking and freezing, and prevents water and sediment from being trapped in the seat. It is designed for emergency safety relief and shall not be used as an operating control.

• Iron body with expanded outlets for hot water space heating boilers
• Seat located above drain, water can't be trapped and sediment can't foul seat
• Non-mechanical seat-to-disc alignment will not stick or freeze
• Each hot water space heating boiler shall be equipped with a pressure relief valve set to relieve below the maximum boiler working pressure
• Water seal of high temperature resisting material isolates spring working parts from water during relief

Sid Harvey Item #:B145-6: Replaces Part #:'s : 24603,
,