Watts regulators series 009 reduced pressure zone assemblies prevent the reverse flow of polluted water from entering into the potable water supply due to backsiphonage and or backpressure. It consists of bronze body construction 1/4 - 2" or FDA approved epoxy coated cast iron 2-1/2 - 3", 2 in-line independent check valves, replaceable check seats with an intermediate relief valve, and ball valve test cocks. Series 009 is ideal for protection of health hazard cross-connections or for containment at the service line entrance.

Single access cover and modular check construction for ease of maintenance
• Top entry - all internals immediately accessible
• Captured springs for safe maintenance
• Internal relief valve for reduced installation clearances
• Replaceable seats for economical repair
• Bronze body construction for durability
• Ball valve test cocks - screwdriver slotted
• Large body passages provides low pressure drop
• Compact, space saving design
• No special tools required for servicing
• 1/4-turn ball valve
  

  Watts Water 009QT-1/2

Danfoss 013G8024 Nickel-Plated Brass Thermostatic Radiator Angle Valve, 1", FPT x MPT Union Tailpiece

Thermostatic radiator valves regulate the flow of hot water or low pressure steam through free-standing radiators, baseboards or convectors in hot water and 2-pipe steam systems
• Valves are fitted with a packing gland assembly that is replaceable while the system is in operation
• EPDM rubber valve disc provides a seal against the valve seat at differential pressures of up to 15 psig in hot water heating systems, while 15 psig for low pressure steam systems
• Manual plastic cap supplied to protect the valve pusHPin and provide manual control of the valve during installation
• Valves remain normally open with no operator mounted
• Brass bonnet, spindle, nickel-plated tailpiece, union nut, EPDM disc, packing O-ring, stainless steel spring
  

  Danfoss 013G8024

Danfoss 013G8044 Nickel-Plated Brass Straight Thermostatic Radiator Valve Body, 3/4", Solder Union

Valve bodies are designed to meet the demands of the residential, commercial and industrial sectors
• Thermostatic radiator valves regulate the flow of hot water or low pressure steam through free-standing radiators, baseboards or convectors in hot water and 2-pipe steam systems
• Valves are fitted with a packing gland assembly that is replaceable while the system is in operation
• EPDM rubber valve disc provides a seal against the valve seat at differential pressures of up to 15 psig in hot water heating systems, while 15 psig for low pressure steam systems
• Manual plastic cap supplied to protect the valve pusHPin and provide manual control of the valve during installation
• Valves remain normally open with no operator mounted
• Brass bonnet, spindle, nickel-plated brass tailpiece, union nut, EPDM disc, packing O-ring, stainless steel spring
  

  Danfoss 013G8044

Watts regulators series 009 reduced pressure zone assemblies prevent the reverse flow of polluted water from entering into the potable water supply due to backsiphonage and or backpressure. It consists of bronze body construction 1/4 - 2" or FDA approved epoxy coated cast iron 2-1/2 - 3", 2 in-line independent check valves, replaceable check seats with an intermediate relief valve, and ball valve test cocks. Series 009 is ideal for protection of health hazard cross-connections or for containment at the service line entrance.

Single access cover and modular check construction for ease of maintenance
• Top entry - all internals immediately accessible
• Captured springs for safe maintenance
• Internal relief valve for reduced installation clearances
• Replaceable seats for economical repair
• Bronze body construction for durability
• Ball valve test cocks - screwdriver slotted
• Large body passages provides low pressure drop
• Compact, space saving design
• No special tools required for servicing
• 1/4-turn ball valve
  

  Watts Water 009QT-3/4

Watts Water BBFP-S Forged Brass Dual Check Backflow Preventer with Series BBFP is specially made for smaller supply lines and ideally suited for laboratory equipment, processing tanks, sterilizers, dairy equipment and similar applications. It is particularly recommended for boiler feed lines to prevent backflow when supply pressure falls below system pressure. Series BBFP is suitable for use on hot or cold water and can be used under continuous pressure. It features a primary check valve utilizing a rubber disc seating against a mating rubber part to ensure tight closing. A secondary check valve utilizes a rubber disc-to-metal seating. In the event of fouling of the downstream check valve, leakage would be vented to atmosphere through the vent port thereby safeguarding the potable water system.

Watts Water 1/2 BBFP-S

VentRite 1VT Nickel-Plated, Hand Polished Brass Adjustable Steam Vent Air Valve, 1/8", Male

All vents are factory assembled, tested and inspected in the USA
• Each vent is individually packed with external labeling for convenience and maintenance
• Our vents have all brass internals with nickel plated and hand polished exterior
• Every Vent-Rite vent is factory assembled, tested and inspected in the USA
• #1 adjustable vent has a wide adjustment conveniently located below steam path

Sid Harvey Item #:1VT: Replaces Part #:'s : B154 | HYD205-B154 |

Vent-Rite Corporation 1VT

Bell & Gossett 113021 Automatic Air Vent, 1/2 x 3/4", FNPT x MNPT, 150 psi, 240 deg F, Brass and Non-Ferrous Internals

Straight body style
• Non ferrous internals
• A full line of manual and automatic air vents designed to remove troublesome air in the system
  

  Bell & Gossett 113021

Bell & Gossett 113222 Automatic Air Vent, 1/8", MNPT, 150 psi, 240 deg F, Brass and Non-Ferrous Internals

A full line of manual and automatic air vents designed to remove troublesome air in the system
• Cast iron, brass and steel construction with non-ferrous internals
• Automatic air vents are designed to vent the accumulation of troublesome air wherever it can be trapped
• Straight body style
  

  Bell & Gossett 113222

Bell & Gossett 113020 Brass Automatic Air Vent, 1/8", MNPT, 35 psi, 240 deg F

Automatic air vents are designed to vent the accumulation of trouble some air wherever it can be trapped
• Non-ferrous internals
• Straight body pattern
  

  Bell & Gossett 113020

Vent-Rite Corporation 11VT Air Vent, 1/8", MNPT, 6 psi, Brass

Every Vent Rite vent is factory assembled, tested & inspected in the USA
• Each valve is individually packaged with external labeling for convenience & maintenance
• All brass internals with nickel plated & hand polished exterior
• Adjustable vents have wide adjustment conveniently located below the steam path
• Vent rite non-vacuum vents are adjustable and all vents are designed for positive action and straight line venting
• They function automatically to vent the air If, through an unusual condition, the vent is filled with water, the vent port automatically closes
• 1/16" vent port
  

  Vent-Rite Corporation 11VT

Bell & Gossett 113041 Brass Drain-O-Tank Air Charger, 1/2", MNPT

The drain-o-tank air charger offers a sure, quick way to recharge a water-logged compression tank


Bell & Gossett 113041

Bell & Gossett 113001 7 Brass Automatic Air Vent, 1/8", FNPT

Designed to vent the accumulation of troublesome air wherever it can be trapped


Bell & Gossett 113001