Sid Harvey 650-52EA High Temperature Maniglass 1200 Gasket Material, 24 x 24,
,

634-1

Tower Equipment KG6 Ball-Joint 5/16"

KG6

Sid Harvey Ball Valve Blow-Down Kit 3/4"

Sid Harvey Item #:B122-10: Replaces Part #:'s : L38-713,
,

Sid Harvey B122-10

Arzel SPD-R0010 Barometric Damper 10" 10AZSPD-R0010

,
,





SPD-R0010

A double-acting control for gas-fired furnaces and boilers is widely used for conversion burner installations, gas draft-induced appliance operation with mechanical draft inducers or sidewall power venters. It is also recommended for use on gas atmospheric appliances where a draft hood cannot be installed and can improve combustion stability and draft on many gas atmospheric installations with venting problems. The MG-1 provides precise, accurate control of drafts at levels higher than permitted by a standard draft diverter, which is a frequent requirement with gas. Because it is double-acting, it opens out to relieve positive vent system pressures as low as 0.01" draft adjustments using weights are simple and accurate from 0.01 - 0.1".

,
,

Field Controls MG1-5

The field RC is furnished as standard equipment on many leading brands of oil or coal-fired heating equipment. It is calibrated to allow for easy adjustment to the furnace or boiler manufacturer's specifications. Designed for settings from 0.02 - 0.08", this control is so sensitive that instrumentation should be used when adjusting the unit during installation.

Sid Harvey Item #:100-24: Replaces Part #:'s : x89-860,
,

Field Controls 100-24

For proper operation and efficient fuel consumption in oil, gas, and/or coal-fired heating appliances, draft must remain constant. When it is, combustion is more complete, fuels are utilized efficiently, and money is saved. Field Draft Controls maintain consistent draft by counteracting the negative forces caused by changes in temperature and barometric pressure, as well as the effects of wind.

• With collar

Sid Harvey Item #:100-20: Replaces Part #:'s : x71-179,

,

Field Controls 100-20

The Field RC is furnished as standard equipment on many leading brands of oil or coal-fired heating equipment. It is calibrated to allow for easy adjustment to the furnace or boiler manufacturers specifications. Designed for settings from 0.02 - 0.08", this control is so sensitive that instrumentation should be used when adjusting the unit during installation.

• 20 ga steel ring and gate, 26 ga collar
• 63.6 sq-inch nominal capacity
• 25-1/4 - 31-1/2 circumference

Sid Harvey Item #:100-26: Replaces Part #:'s : 6H101,
,

Field Controls 100-26

Field Controls 01950201 10" M+MG2 barometric draft control for gas and oil type M+MG2 barometric draft controls overview solid, oil or gas commercial/industrial, this is a series of compact, rugged, heavy-duty controls for use on large residential, commercial, and industrial applications. The Field Type M+MG2 draft control provides precise draft regulations for solid fuels, oil, gas, or oil/gas appliances requiring only the simplest, on-the-job adjustments depending on which fuel is to be utilized. In a gas installation, the double-acting Type M+MG2 is specified instead of a draft hood to give the appliance the assistance of the chimney. In a duel fuel oil/gas or a gas-fired only application, use the M+MG2 as a double-acting draft control with the optional Field Thermal Switch accessory. Use the M+MG2 as a single-acting draft control for oil or solid fuel applications. For any installation with 10" or larger diameter vent pipe, specify our standard M+MG2 Draft Control, the unit that can be adapted to any fuel. The moving part (gate) rests on a long, thin, stainless steel knife edge which, in turn, is supported by self-aligning and self-cleaning bearings. When the heavy gauge gate moves, only the knife edge rests on the bearing for minimum friction and maximum sensitivity to draft changes.

Sid Harvey Item #:100-4: Replaces Part #:'s : 111,
,

Field Controls 100-4

The field RC is furnished as standard equipment on many leading brands of oil or coal-fired heating equipment. It is calibrated to allow for easy adjustment to the furnace or boiler manufacturer's specifications. Designed for settings from 0.02 - 0.08", this control is so sensitive that instrumentation should be used when adjusting the unit during installation.

Sid Harvey Item #:100-30: Replaces Part #:'s : x71-292,
,

Field Controls 100-30

Field Controls 00963801 Silver Barometric Draft Control for Residential Oil, Wood and Coal, 6"

• M control lends itself ideally to conditions requiring a great deal of stability and accuracy
• Designed for settings from 0.01 - 0.1"
• Type M features an infinitely variable screw adjustment, permitting an extremely fine instrument setting
• M employs side wings to control air direction with gate curvatures designed to compensate for differences in horizontal and vertical settings

Sid Harvey Item #:100: Replaces Part #:'s : 29218,
,

100

The field RC is furnished as standard equipment on many leading brands of oil or coal-fired heating equipment. It is calibrated to allow for easy adjustment to the furnace or boiler manufacturer's specifications. Designed for settings from 0.02 - 0.08", this control is so sensitive that instrumentation should be used when adjusting the unit during installation.

Sid Harvey Item #:100-22: Replaces Part #:'s : x71-184,
,

Field Controls 100-22