Refrigeration Research 1921 Liquid Receiver Tank Assembly 4" x 10" 4 LBS,
,

Refrigeration Research 1918 Liquid Receiver 5" x 10" 6 Pounds,
,

Refrigeration Research 5315 Refrigeration Receiver, 6 lb Capacity, 3/8" SAE Inlet x 3/8" SAE Valve Outlet, 10" L x 5" Diameter

• Refrigeration research receivers have been made continuously for over 50 years
• They are used widely by original equipment manufacturers throughout the industry
• They are backed by a reputation for quality and service
• These receivers with valves and fittings attached are hydrogen brazed for cleanliness and pressure tested for reliability
• 430 deg F fusible plug is installed on all receivers except #2030, #2039, and #9028
• All valves are supplied with steel stem caps with copper gaskets and brass flare nuts and caps, all receivers are powder coated for excellent corrosion resistance
• Pressure tested for 500 psi maximum working pressure

,
,

Refrigeration Research 1911 Liquid Receiver 6" x 12" 10 Pounds 3/8" Flare x 3/8" Flare,
,

Refrigeration Research 3212 Liquid Receiver Tank Assembly 6" x 8" 16 LBS,

,

White Rodgers Cooling Controls AOFD is designed specifically for refrigerant systems that use POE oil. The AOFD protects compressors by removing moisture and trapping contaminants. Oil Filter Drier, 3/8", Male Flare

• Designed to clean and dry POE oil
• 3/8" male flare connections for easy replacement
• 3 micron filtration for optimum oil cleaning
• Large filter surface area to provide maximum filtration
• Contains desiccant for moisture removal
• Designed to operate at a very low pressure drop
• Dual access valves for pressure drop monitoring

,

White Rodgers Cooling Controls AOFD553

Parker Oil Filter Drier

• 3/8" W/Tap
  The design of the OF-303 is similar to the OF-303-BP, but the OF-303 is supplied without the bypass feature. The OF-303-T is similar to the OF-303 except an access fitting is added to assist with pressure drop monitoring. OF Series Oil Filters can be installed in a horizontal or vertical position.,
  ,
  
  

Henry Technologies S-5587 Non Serviceable Conventional Oil Separator, 7/8" ODS, 3/8" SAE Return, 1/8" NPT Drain

• The function of a helical oil separator is to remove oil from the discharge gas and return it to the compressor either directly or through an oil management system
• Conventional oil separators can be used in a wide variety of applications, common applications include multi-compressor racks and remote condensing units
• These separators are designed for use with scroll and reciprocating type compressors, they are not recommended for screw or rotary vane compressors
• Conventional oil separators are intended for low pressure oil management systems
• ODS refrigerant connection
• SAE flare oil connections
• Low pressure drop
• No moving parts within oil separation zone
• Magnet on oil float to collect debris
• The main components- shell, end caps and connections are made from carbon steel
• The separation screens are made from brass
• The float assemblies are made from stainless steel, brass and copper

,
,

Henry Technologies A-1900-30 Replacement Bottom Plate Float Assembly.

,
,

Henry Technologies A-1900-30

Henry Technologies 2-023-001

• Oil Separator Gasket for 1900 Series,
  ,
  
  

Henry Technologies S-8066 Receiver Vertical 3/8" Flare x 1/2" Flare,
,

Air conditioning, heat pump, truck refrigeration and many other applications require intermittent operation of the refrigeration compressor. Especially in remote applications, the suction line may trap or hold quantities of liquid which are suddenly dumped into the compressor as it starts up. This is frequently the cause of broken valves, pisTons, broken or bent connecting rods, blown gaskets and bearing washout. Proper installation of the Refrigeration Research suction accumulator in the suction line, just before the compressor, eliminates damage. If correctly sized, relatively large quantities of liquid refrigerant may return through the suction line and the suction accumulator prevents damage to the compressor. Liquid is temporarily held in the suction accumulator and metered back to the compressor along with any oil, at a controlled rate, through the metering orifice. Therefore, damage to the compressor is prevented and the compressor immediately and quietly goes to work.

,
,