Brand Name
BTU
Voltage
Position
|◀ 61 - 71 of 71 ▶|
View:
Fujitsu FH4821TPSASN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections
    48K BTU 4 Ton
  • 115/1 VAC
  • 21" Wide
  • PSC Motor
  • Multi-Position,
    FUJITSU FH4821TPSJSN

    Fujitsu FH4821TPSJSN

Item#:
FH4821TPSJSN
Manufacturer Item:
FH4821TPSJSN
Manufacturer:
FUJITSU
Fujitsu FH3017TPSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections
  • 42K BTU 3-1/2 Ton
  • 208/230/1 VA
  • 21" Wide
  • PSC Motor
  • Multi-Position,




    FUJITSU FH4221TPSJSN

Item#:
FH4221TPSJSN
Manufacturer Item:
FH4221TPSJSN
Manufacturer:
FUJITSU
Fujitsu FH4821TPSASN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections
    48K BTU 4 Ton
  • 208/230/1 VAC
  • 21" Wide
  • Multi-Position,

    Fujitsu FH4821TTSJSN

Item#:
FH4821TTSJSN
Manufacturer Item:
FH4821TTSJSN
Manufacturer:
FUJITSU
  • 11/2 thru 5 tons
  • Available for Environmentally Sound R410A systems
  • TXV metering device factory installed
  • ECM motor
  • Copper tube / aluminum fin coil on standard models
  • Available with industry exclusive tin coated copper main tubing for additional corrosion protection
  • Sweat connections
  • Primary and secondary drain fittings with brass inserts
  • 3 amp automotive type fuse in wire harness
  • Multiple electrical entry locations
  • Time delay relay (TDR) programmed in motor
  • Field installed heater packages from 5 kW  30 kW available separately
  • HUD approved for manufactured housing
  • 208/230160 supply voltage
  • Units tested and certified by manufacturer to achieve a 2% or less leakage rate at 1.0 inch water column
  • 1 inch thick insulation with R value of 4.2
  • Multiposition installation  upflow or horizontal left standard, horizontal right with minor modification (field convertible to downflow with available accessory kit
  • No Heat (Plug) Kit factory installed
  • Filter (washable) factory supplied
  • TXV metering device factory installed
  • ECM motor
  • Copper tube / aluminum fin coil on standard models Available with industry exclusive tin coated copper main tubing for additional corrosion protection
  • Sweat connections
  • Primary and secondary drain fittings with brass inserts
  • 3 amp automotive type fuse in wire harness
  • Multiple electrical entry locations
  • Time delay relay (TDR) programmed in motor
  • Field installed heater packages from 5 kW  30 kW available separately
  • HUD approved for manufactured housing
  • 208/230160 supply voltage
  • Units tested and certified by manufacturer to achieve a 2% or less leakage rate at 1.0 inch water column
  • 1 inch thick insulation with R value of 4.2
  • Multiposition installation  upflow or horizontal left
    standard, horizontal right with minor modification (field convertible to downflow with available accessory kit)
  • No Heat (Plug) Kit factory installed
  • Filter (washable) factory supplied

    International Comfort Products FXM4X4800AL

  • Item#:
    FXM4X4800AL
    Manufacturer Item:
    FXM4X4800AL
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
  • 11/2 thru 5 tons
  • Available for Environmentally Sound R410A systems
  • TXV metering device factory installed
  • ECM motor
  • Copper tube / aluminum fin coil on standard models
  • Available with industry exclusive tin coated copper main tubing for additional corrosion protection
  • Sweat connections
  • Primary and secondary drain fittings with brass inserts
  • 3 amp automotive type fuse in wire harness
  • Multiple electrical entry locations
  • Time delay relay (TDR) programmed in motor
  • Field installed heater packages from 5 kW  30 kW available separately
  • HUD approved for manufactured housing
  • 208/230160 supply voltage
  • Units tested and certified by manufacturer to achieve a 2% or less leakage rate at 1.0 inch water column
  • 1 inch thick insulation with R value of 4.2
  • Multiposition installation  upflow or horizontal left standard, horizontal right with minor modification (field convertible to downflow with available accessory kit
  • No Heat (Plug) Kit factory installed
  • Filter (washable) factory supplied
  • TXV metering device factory installed
  • ECM motor
  • Copper tube / aluminum fin coil on standard models Available with industry exclusive tin coated copper main tubing for additional corrosion protection
  • Sweat connections
  • Primary and secondary drain fittings with brass inserts
  • 3 amp automotive type fuse in wire harness
  • Multiple electrical entry locations
  • Time delay relay (TDR) programmed in motor
  • Field installed heater packages from 5 kW  30 kW available separately
  • HUD approved for manufactured housing
  • 208/230160 supply voltage
  • Units tested and certified by manufacturer to achieve a 2% or less leakage rate at 1.0 inch water column
  • 1 inch thick insulation with R value of 4.2
  • Multiposition installation  upflow or horizontal left
    standard, horizontal right with minor modification (field convertible to downflow with available accessory kit)
  • No Heat (Plug) Kit factory installed
  • Filter (washable) factory supplied

    INTERNATIONAL COMFORT PRODUCTS FXM4X4200AL

  • Item#:
    FXM4X4200AL
    Manufacturer Item:
    FXM4X4200AL
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
  • 11/2 thru 5 tons
  • Available for Environmentally Sound R410A systems
  • TXV metering device factory installed
  • ECM motor
  • Copper tube / aluminum fin coil on standard models
  • Available with industry exclusive tin coated copper main tubing for additional corrosion protection
  • Sweat connections
  • Primary and secondary drain fittings with brass inserts
  • 3 amp automotive type fuse in wire harness
  • Multiple electrical entry locations
  • Time delay relay (TDR) programmed in motor
  • Field installed heater packages from 5 kW  30 kW available separately
  • HUD approved for manufactured housing
  • 208/230160 supply voltage
  • Units tested and certified by manufacturer to achieve a 2% or less leakage rate at 1.0 inch water column
  • 1 inch thick insulation with R value of 4.2
  • Multiposition installation  upflow or horizontal left standard, horizontal right with minor modification (field convertible to downflow with available accessory kit
  • No Heat (Plug) Kit factory installed
  • Filter (washable) factory supplied
  • TXV metering device factory installed
  • ECM motor
  • Copper tube / aluminum fin coil on standard models Available with industry exclusive tin coated copper main tubing for additional corrosion protection
  • Sweat connections
  • Primary and secondary drain fittings with brass inserts
  • 3 amp automotive type fuse in wire harness
  • Multiple electrical entry locations
  • Time delay relay (TDR) programmed in motor
  • Field installed heater packages from 5 kW  30 kW available separately
  • HUD approved for manufactured housing
  • 208/230160 supply voltage
  • Units tested and certified by manufacturer to achieve a 2% or less leakage rate at 1.0 inch water column
  • 1 inch thick insulation with R value of 4.2
  • Multiposition installation  upflow or horizontal left
    standard, horizontal right with minor modification (field convertible to downflow with available accessory kit)
  • No Heat (Plug) Kit factory installed
  • Filter (washable) factory supplied

    INTERNATIONAL COMFORT PRODUCTS FXM4X2400AL

  • Item#:
    FXM4X2400AL
    Manufacturer Item:
    FXM4X2400AL
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
    Mortex H41-46-26-A1BC Air Handler Hot Water Hydronic 1-1/2-2 Ton 115 VAC
      Upflow, Horizontal (right to left)
    • Drain pans are manufactured of durable, non-corrosive plastic, and meet ASHRAE standards for IAQ. Pans are"dry" thus holding minimum water.
    • Drain pans have primary and secondary drains for either left or right hand connections.
    • Cabinet is heavy gauge embossed Gallonvanized steel substrate, with front and top panels pre-painted a durable neutral gray.
    • All units are equipped with factory installed time delay relay as standard.
    • All units have 1 foil faced insulation.
    • All units include a 1" throw away filter.
    • All electric heat units are 208/230/1/60 All hydronic heat units are 115/1/60.
    • Standard units with 12 KW electric heat or larger have a factory installed circuit breaker (UL Requirement). All units 10 KW and smaller may be ordered with or without the circuit breaker option.
    • All units are suitable for"0"" clearance to combustible materials.
    • Electric heat units are field convertible to downflow with factory conversion kit.
    • Blower assembly slides out for easy maintenance.
    • Refrigeration coil connections are swaged and then factory sealed with copper caps to maintain a nitrogen holding charge.
    • All hydronic units include a freeze protection switch.
    • All hydronic units include a compressor lockout switch.

      Mortex Products H41-46-26-A1BC

    Item#:
    H41-46-26-A1BC
    Manufacturer Item:
    H41-46-26-A1BC
    Manufacturer:
    MORTEX PRODUCTS, INC.
    First Company 30HBXB-HW Baked-On Powder-Coated Variable Speed Hydronic Air Handler with TXV Metering Device R410A, 30000 BTU Cooling, 58900 BTU Heating, 2.5 Ton, 120 VAC
    • Multi-function micro-processor circuit board
    • Blower start relay - eliminates field installed boiler relay, allowing direct wiring from the boiler to the air handler
    • Manual air vent on hot water coil
    • Blower door shut-off switch
    • Slide-out hot water coil for easier service
    • 2-speed fan operation
    • Convertible horizontal drain pan
    • PisTon type metering device (standard)
    • Copper tube heating and cooling coils
    • Compatible with all major brands of split condensing units and heat pumps
    • Primary and secondary condensate drain connections
    • Factory installed filter drier
    • 1" filter easily accessible
    • Without pump
    ,
    ,


    First Company 30HBXB-HW-TXV410

    Item#:
    30HBXB-HW-TXV410
    Manufacturer Item:
    30HBXB-HW-TXV410
    Manufacturer:
    FIRST CO.
    First Company 60HBXB-HW-R410A-TXV Air Handler Hydronic Variable Speed W/TXV 5 Ton
    • Multi function micro-processor circuit board
    • Blower start relay - eliminates field installed boiler relay, allowing direct wiring from the boiler to the air handler
    • Manual air vent on hot water coil
    • Blower door shut-off switch
    • Slide out hot water coil for easier service
    • 2-speed fan operation
    • Convertible horizontal drain pan
    • PisTon type metering device (standard)
    • Copper tube heating and cooling coils
    • Compatible with all major brands of split condensing units and heat pumps
    • Primary and secondary condensate drain connections
    • Factory installed filter drier
    • 1" filter easily accessible
    • Without pump



      First Company 60HBXB-HW-R410A-TXV

    Item#:
    60HBXB-HW-R410A-TXV
    Manufacturer Item:
    60HBXB-HW-R410A-TXV
    Manufacturer:
    FIRST CO.
    Industry Standard R-410A Refrigerant
  • Models featuring Electric Heat without Indoor Cooling Coil
  • Quiet and efficient X-13 (ECM) motor technology
  • Only 35" tall and 4-way convertible for all those tight spaces
  • Available from factory in upflow and horizontal configurations
  • Nominal airflow up to 0.5" external static pressure with reduced airflow up to 1.0" external static pressure
  • Factory installed MultiFlex coils
  • Sturdy steel construction with 1 inch [25.4 mm] of foil faced insulation for excellent sound and insulating characteristics
  • Permanent, easily accessible and washable filter furnished standard
  • Circuit breaker (standard on units with more than 11 kW) meets U.L. and cUL requirements for service disconnect
  • Factory installed auxiliary electric heat provides exact heat for indoor comfort over a variety of applications
  • Fan settings for selectable, customized cooling airflow over a wide variety of applications
  • Cabinet air leakage less than 2% at 1 inch H2O when tested in accordance with ASHRAE standard 193


    Fujitsu FB17TSA00N

  • Item#:
    FB17TSA00N
    Manufacturer Item:
    FB17TSA00
    Manufacturer:
    FUJITSU
    Fujitsu FH6024TTSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
    The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connectionsFujitsu FH6024TTSJSN

    Fujitsu FH6024TTSJSN

    Item#:
    FH6024TTSJSN
    Manufacturer Item:
    FH6024TTSJSN
    Manufacturer:
    FUJITSU
    |◀ 61 - 71 of 71 ▶|
    View: