RectorSeal EZT-406 Flexible Rod Cleaning Brush

• 18",
  ,
  
  
  

  RectorSeal EZT-406

Diversitech DDS-3 Pull-Out Fusible Disconnect Switch, 3 amp, Import

,
,

Diversitech DDS-60 Metal Fusible Pull-Out Disconnect Switch, 60 amp at 240 VAC

• Convenient design allows for easy access to controls via wide-opening, reversible door with full dead front
• Fused models benefit from having fuses located in easy pull-out handle with indicator lights for blown fuses
• Line, load and ground terminals aligned for easy wiring
• Folding pullout handle - low profile
• Folding pivot locking tab
• Installs without removing internals
• This is rain tight and sleet resistant

Sid Harvey Item #:E348-22: Replaces Part #:'s : 14043 | 14045 |,
,

White Rodgers Cooling Controls Epoxy Powder Painted Bi-Directional Liquid Line Filter Drier, 3/8" Flare

• Internal check valves allow flow and filtration in either direction, eliminates need for external check valves
• High moisture and acid removal capacity
• Approved for POE oils with Copeland compressor
• Desiccant blend: optimized for high water capacity and acid capacity
• Corrosion resistant epoxy powder paint finish,
  

White Rodgers Cooling Controls Epoxy Powder Painted Bi-Directional Liquid Line Filter Drier, 3/8" OD

• Internal check valves allow flow and filtration in either direction, eliminates need for external check valves
• High moisture and acid removal capacity
• Approved for POE oils with Copeland compressor
• Desiccant blend: optimized for high water capacity and acid capacity
• Corrosion resistant epoxy powder paint finish,
  
  
  

  White Rodgers Cooling Controls D14-97

White Rodgers Cooling Controls Epoxy Powder Painted Bi-Directional Liquid Line Filter Drier, 3/8" OD

• Internal check valves allow flow and filtration in either direction, eliminates need for external check valves
• High moisture and acid removal capacity
• Approved for POE oils with Copeland compressor
• Desiccant blend: optimized for high water capacity and acid capacity
• Corrosion resistant epoxy powder paint finish,

White Rodgers Cooling Controls Epoxy Powder Painted Bi-Directional Liquid Line Filter Drier, 3/8" OD

• Internal check valves allow flow and filtration in either direction, eliminates need for external check valves
• High moisture and acid removal capacity
• Approved for POE oils with Copeland compressor
• Desiccant blend: optimized for high water capacity and acid capacity
• Corrosion resistant epoxy powder paint finish,
  
  

Diversitech HPR-3-2PG Heat Pump Riser 2 Piece 3" Black

Diversitech HPR-3 1-Piece Heat Pump Riser
DiversiTech's Heat Pump Riser provides the desired elevation for condensers, heat pumps, and air handlers. The one-piece, heavy-duty plastic unit is manufactured in three heights. Butyl mastic on the top and bottom guarantees no slipping and reduced vibration and noise. Available in 1 or 2 piece risers. Four risers can handle up to 2,000 lb uniform load.,
,

Diversitech HPR-3

Diversitech HPR-6 1-Piece Heat Pump Riser
DiversiTech's Heat Pump Riser provides the desired elevation for condensers, heat pumps, and air handlers. The one-piece, heavy-duty plastic unit is manufactured in three heights. Butyl mastic on the top and bottom guarantees no slipping and reduced vibration and noise. Available in 1 or 2 piece risers. Four risers can handle up to 2,000 lb uniform load.,

Diversitech HPR-6

Diversitech HP3232-8 Heat Pump Riser Pad 32" L x 32" W x 8" H for Use With Heat Pump Equipment
Provides an effective base for heat pump equipment installed in snowy climates. Rather than a combination of a typical 2" (or 3") equipment pad and 6in. Heat pump risers, the Heat Pump Pad provides a full 8" of elevation in a simple square footprint. The star pattern of the integral risers allows for installation of equipment with different size footprints up to 36 x 36". Also included are eight anti-vibration pads uniquely designed to fit into the guide slots on the top of the integral risers. The base is sloped outward to allow for easy drainage of condensate or defrost cycle condensate when the outdoor coil is operating in heat pump mode. Nestable for efficient shipping, transportation, and warehousing. Injection molded from concrete gray, recycled polypropylene material, the Heat Pump Pad is environmentally friendly and designed to last longer than the equipment it supports. US Patent Number 7,891,635, and other patent(s) pending.

,
,

Diversitech HP3232-8

Diversitech HP3636-8 Heat Pump Riser Pad 36" L x 36" W x 8" H for Use With Heat Pump Equipment
Provides an effective base for heat pump equipment installed in snowy climates. Rather than a combination of a typical 2" (or 3") equipment pad and 6in. Heat pump risers, the Heat Pump Pad provides a full 8" of elevation in a simple square footprint. The star pattern of the integral risers allows for installation of equipment with different size footprints up to 36 x 36". Also included are eight anti-vibration pads uniquely designed to fit into the guide slots on the top of the integral risers. The base is sloped outward to allow for easy drainage of condensate or defrost cycle condensate when the outdoor coil is operating in heat pump mode. Nestable for efficient shipping, transportation, and warehousing. Injection molded from concrete gray, recycled polypropylene material, the Heat Pump Pad is environmentally friendly and designed to last longer than the equipment it supports. US Patent Number 7,891,635, and other patent(s) pending.

,
,

Diversitech HP3636-8