Brand Name
Part Type
Category

All Clearance items are limited to quantity on hand in each location. 

  1. Use the ( NARROW YOUR SEARCH ) option on the left to filter items. 
  2. Click ( DISPLAY COMPANY INVENTORY ) to view quantity on hand of selected item if not available in your primary location. 
|◀ ◀ 49 - 60 of 61 ▶ ▶|
View:

Hot Water Heater Residential Concentric Direct Vent Min BTU 199,000 120 VAC Propane

Noritz NR981-DVC-LP Residential Concentric Direct Vent Hot Water Heater Min BTU BTU 199,000 120 VAC Propane,
,

Item#:
NR981-DVC-LP
Manufacturer Item:
NR981-DVC-LP
Manufacturer:
NORITZ
 
NR981-DVC-LP-Parts_Misc
NR981-DVC-LP_Install
NR981-DVC-LP_Spec

ICP Heat Pump Condensing Unit 1-Stage 2.5 Ton

REFRIGERATION CIRCUIT

Copeland Scroll compressors on select models

Suction line accumulator factory installed

Bi- flow filter- drier included for field installation

Integrated solid state control with Time- Temperature Defrost

External high and low refrigerant service ports

copper tube / aluminum fin coil

PERFORMANCE

Communicating, self- configuring operation when used with Observer Wall Control (TSTAT0201CW)

Outdoor temperature sensor factory installed

Compressor sound blanket standard

Isolation compressor grommets
Item#:
TSH430GKA
Manufacturer Item:
TSH430GKA
Manufacturer:
INTERNATIONAL COMFORT PRODUCTS
 
TSH430GKA_Spec

ICP Heat Pump Condensing Unit High Efficiency 1.5 Ton


  • Copeland Scroll compressors on all models
  • Suction line accumulator factory installed
  • Bi- flow filter- drier included for field installation
  • Integrated solid state control with Time- Temperature Defrost
  • Low pressure switch
  • Copper tube/aluminum fin coil
  • Easy Access service valves on all models
  • External high and low refrigerant service ports
  • Only two screws to access control panel
  • Factory charged with R410A refrigerant
  • Baked- on powder coat finish over Gallonvanized steel
  • Post- painted (black) coil fins
  • Coated, weather- resistant cabinet screws
  • Coated inlet grille with 3/8grille spacing for extra protection
  • 5 year compressor limited warranty
  • 5 year parts limited warranty (including compressor and coil) - With timely registration, an additional 5 year parts limited warranty (including compressor and coil
Item#:
NXH618GKP
Manufacturer Item:
NXH618GKP
Manufacturer:
INTERNATIONAL COMFORT PRODUCTS
 
NXH6-ICP-Service_Misc
NXH6-ICP_Broc
NXH6-ICP_Install
NXH618GKP_Spec

Mainline Variable Speed Gas Heating Furnace 33-1/3" H x 17-1/2" W x 29" D

  • G8MVL Series Steel 2-Stage Mainline Variable Speed Gas Furnace,
    • Supports 2-stage cooling units
    • Flame roll-out sensors standard
    • Dehumidification feature in cooling
    • 24 VAC humidifier terminal and electronic air cleaner terminal
    • Tougher - variable speed blower motor, adjustable heating blower off delay, factory set blower on delay, RPJ aluminized steel heat exchanger, high temperature limit control prevents overheating, direct ignition with silicon nitride igniter, 1-piece preprinted steel cabinet
    • Quieter - 2-stage heating operation, 2-stage induced draft blower, in-shot burners, insulated blower compartment
    • Innovative knobs for easy door removal and secure attachment
    • Through the casing flue pipe for counterflow or horizontal applications with accessory
    • 4-position - upflow/downflow/horizontal installation
    • 3-position vent elbow capability
    • Slide out blower assembly
    • 10 years no hassle replacement, 5 years parts and 20 years heat exchanger limited warranty
    • Solid state time operation heating blower control
    • 4.5 - 13.6" WC inlet gas pressure
    • Low NOx
    • Item#:
    G8MVL0701716
    Manufacturer Item:
    G8MVL0701716B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G8MVL0701716_Spec

    Natural Gas Fired Cast Iron Water Boiler 58K BTU 84% AFUE Fan Induced

    Weil-McLain CGI3PI Natural Gas Fired Cast Iron Water Boiler 58K BTU 84% AFUE

    Item#:
    CGI3PI
    Manufacturer Item:
    381-357-858
    Manufacturer:
    WEIL-MCLAIN
     
    CGI-Weil-Mclain-Parts-Misc
    CGI3PI_Install
    CGI3PI_Spec

    Natural Gas Fired Cast Iron Water Boiler 58K BTU 84% AFUE High Altitude Fan Induced

    Weil-McLain CGI3PIN-HALT Natural Gas Fired Cast Iron Water Boiler 58K BTU 84% AFUE High Altitude

    Item#:
    CGI3PIN-HALT
    Manufacturer Item:
    381-359-033
    Manufacturer:
    WEIL-MCLAIN
     
    CGI-Weil-Mclain-Parts-Misc
    CGI3PIN-HALT_Install

    Oil Burner Carlin Williamson

    Williamsom-Thermoflo Parts CB-BLR-145-S2 Oil Burner Williamson
      ,

    Item#:
    CB-BLR-145-S2
    Manufacturer Item:
    CB-BLR-145-S2
    Manufacturer:
    CARLIN COMBUSTION TECHNOLOGY

    OUTDOOR HT PUMP 30K BTU >>LIMITED STOCK CLEARANCE ITEM<<

    Item#:
    PUZ-A30NHA7
    Manufacturer Item:
    PUZ-A30NHA7
    Manufacturer:
    MITSUBISHI ELECTRIC US, INC.

    Series 80 Steam Trim Pack B

    Item#:
    385802500
    Manufacturer Item:
    385-802-500
    Manufacturer:
    WEIL-MCLAIN

    Unit Heater Suspended Hydronic 110,000 (High) 78,000 (Low) Copper Tube/Alumimun Fins

  • Reznor Model WS Steam/Hot Water Suspended Heaters are design-engineered to be technically advanced and esthetically pleasing which makes it the hydronic heater for the 21st century.
    This smart new concept in commercial heating units will accommodate all architects who are looking for something new and different.
  • The heating range of Model WS is 13,000 to 350,000 BTUH. The air volume ranges from 270 to 4,750 CFM.
  • The heat exchanger is made of one or two rows of steel coils (standard or optional copper coils) with aluminum
  • The standard steel tubing is very strong and long lasting. Steel tubing is designed for hot water applications up to 150 psi.
  • The copper tubing used for the heating coil is very thick (0.03, 0.75 mm), making Reznor heating coils extremely sturdy and long lasting. The copper tube diameter is 0.867 (22 mm) O.D. The large tube diameter reduces the water pressure drop, which means these units require lower pump pressure than other hydronic heaters. It also allows a very rapid heat radiation. For steam heating applications copper tube (Option HA12) is required. Designed for high working steam pressure up to 145 psi (10 bar), every heat exchanger is subjected to a pressure test at over 350 psi (25 bar) before leaving the factory.
  • The heat exchanger assembly receives a special epoxy-polyester powder coating which makes the coil long lasting and increases the thermal output.
  • The Fan/Motor Assembly is made up of three components: the fan, the motor and the fan guard, which also acts as the main support for the fan. This fan guard is galvanized for protection against corrosion, and is mounted onto the main casing with anti-vibration rubber mountings. The fan guard meets OSHA requirements.*
  • The standard 2-speed motor is a hermetically sealed motor which is maintenance free. The motor is wired for Data Chart for fan RPM, heating output and CFM ranges. output, or low speed for reduced noise level. All motors have internal protection as a standard feature.
  • All Model WS units can be installed for either vertical or horizontal discharge.
  • pre-painted steel helps protect the cabinet against oxidation.
  • The cabinet is held together by shake-proof screws and molded corner sections to add additional strength and installation.
  • The optional Air Flow Induction Optimizer is available for horizontally discharged units. The Air Flow Induction the heated air stream. See the optional accessories section for more information.
  • Units are packaged into strong corrugated cardboard cartons with strengthened upper and lower side sections. These containers are clearly marked with the model number, size and approximate shipping weight.
  • Units are manufactured in an ISO 9001 registered facility.

    • Item#:
    WS78/110
    Manufacturer Item:
    WS78/110
    Manufacturer:
    NORTEK GLOBAL(REZNOR)
     
    WS-Series-Broc
    WS-Series-Install
    WS-Series-Spec

    Unit Heater Suspended Hydronic 110,000 (High) 78,000 (Low) Copper Tube/Alumimun Fins

  • Reznor Model WS Steam/Hot Water Suspended Heaters are design-engineered to be technically advanced and esthetically pleasing which makes it the hydronic heater for the 21st century.
    This smart new concept in commercial heating units will accommodate all architects who are looking for something new and different.
  • The heating range of Model WS is 13,000 to 350,000 BTUH. The air volume ranges from 270 to 4,750 CFM.
  • The heat exchanger is made of one or two rows of steel coils (standard or optional copper coils) with aluminum
  • The standard steel tubing is very strong and long lasting. Steel tubing is designed for hot water applications up to 150 psi.
  • The copper tubing used for the heating coil is very thick (0.03, 0.75 mm), making Reznor heating coils extremely sturdy and long lasting. The copper tube diameter is 0.867 (22 mm) O.D. The large tube diameter reduces the water pressure drop, which means these units require lower pump pressure than other hydronic heaters. It also allows a very rapid heat radiation. For steam heating applications copper tube (Option HA12) is required. Designed for high working steam pressure up to 145 psi (10 bar), every heat exchanger is subjected to a pressure test at over 350 psi (25 bar) before leaving the factory.
  • The heat exchanger assembly receives a special epoxy-polyester powder coating which makes the coil long lasting and increases the thermal output.
  • The Fan/Motor Assembly is made up of three components: the fan, the motor and the fan guard, which also acts as the main support for the fan. This fan guard is galvanized for protection against corrosion, and is mounted onto the main casing with anti-vibration rubber mountings. The fan guard meets OSHA requirements.*
  • The standard 2-speed motor is a hermetically sealed motor which is maintenance free. The motor is wired for Data Chart for fan RPM, heating output and CFM ranges. output, or low speed for reduced noise level. All motors have internal protection as a standard feature.
  • All Model WS units can be installed for either vertical or horizontal discharge.
  • pre-painted steel helps protect the cabinet against oxidation.
  • The cabinet is held together by shake-proof screws and molded corner sections to add additional strength and installation.
  • The optional Air Flow Induction Optimizer is available for horizontally discharged units. The Air Flow Induction the heated air stream. See the optional accessories section for more information.
  • Units are packaged into strong corrugated cardboard cartons with strengthened upper and lower side sections. These containers are clearly marked with the model number, size and approximate shipping weight.
  • Units are manufactured in an ISO 9001 registered facility.

    • Item#:
    WS78/110C
    Manufacturer Item:
    WS78/110C
    Manufacturer:
    NORTEK GLOBAL(REZNOR)
     
    WS-Series-Broc
    WS-Series-Install
    WS-Series-Spec

    Water Heater Atmospheric Vent Residential Tall 36K BTU 50 Gallon LP Gas

    Rheem Water Heaters PROG50-36PRH60H Hot Water Heater Atmospheric Vent Residential Tall 36K BTU 50 Gallon

    Item#:
    PROG50-36PRH60H
    Manufacturer Item:
    PROG50-36P RH60 H
    Manufacturer:
    RHEEM SALES COMP(WATER HTR)
     
    PROG50-36PRH60H_Install
    PROG50-36PRH60H_Spec
    |◀ ◀ 49 - 60 of 61 ▶ ▶|
    View: