Brand Name
Type
Fuel Type
BTU Input
BTU Output
AFUE
Voltage
Phase
|◀ ◀ 61 - 64 of 64 ▶ ▶|
View:

Unit Heater Power Vented 200K BTU 120 VAC

Modine PDP200AE0130 Unit Heater Power Vented 200K BTU 120 VAC,

Item#:
PDP200AE0130
Manufacturer Item:
PDP200AE0130
Manufacturer:
MODINE MFG COMPANY
 
Modine-Catalog_Misc

Unit Heater Suspended Hydronic 110,000 (High) 78,000 (Low) Copper Tube/Alumimun Fins

  • Reznor Model WS Steam/Hot Water Suspended Heaters are design-engineered to be technically advanced and esthetically pleasing which makes it the hydronic heater for the 21st century.
    This smart new concept in commercial heating units will accommodate all architects who are looking for something new and different.
  • The heating range of Model WS is 13,000 to 350,000 BTUH. The air volume ranges from 270 to 4,750 CFM.
  • The heat exchanger is made of one or two rows of steel coils (standard or optional copper coils) with aluminum
  • The standard steel tubing is very strong and long lasting. Steel tubing is designed for hot water applications up to 150 psi.
  • The copper tubing used for the heating coil is very thick (0.03, 0.75 mm), making Reznor heating coils extremely sturdy and long lasting. The copper tube diameter is 0.867 (22 mm) O.D. The large tube diameter reduces the water pressure drop, which means these units require lower pump pressure than other hydronic heaters. It also allows a very rapid heat radiation. For steam heating applications copper tube (Option HA12) is required. Designed for high working steam pressure up to 145 psi (10 bar), every heat exchanger is subjected to a pressure test at over 350 psi (25 bar) before leaving the factory.
  • The heat exchanger assembly receives a special epoxy-polyester powder coating which makes the coil long lasting and increases the thermal output.
  • The Fan/Motor Assembly is made up of three components: the fan, the motor and the fan guard, which also acts as the main support for the fan. This fan guard is galvanized for protection against corrosion, and is mounted onto the main casing with anti-vibration rubber mountings. The fan guard meets OSHA requirements.*
  • The standard 2-speed motor is a hermetically sealed motor which is maintenance free. The motor is wired for Data Chart for fan RPM, heating output and CFM ranges. output, or low speed for reduced noise level. All motors have internal protection as a standard feature.
  • All Model WS units can be installed for either vertical or horizontal discharge.
  • pre-painted steel helps protect the cabinet against oxidation.
  • The cabinet is held together by shake-proof screws and molded corner sections to add additional strength and installation.
  • The optional Air Flow Induction Optimizer is available for horizontally discharged units. The Air Flow Induction the heated air stream. See the optional accessories section for more information.
  • Units are packaged into strong corrugated cardboard cartons with strengthened upper and lower side sections. These containers are clearly marked with the model number, size and approximate shipping weight.
  • Units are manufactured in an ISO 9001 registered facility.

    • Item#:
    WS78/110
    Manufacturer Item:
    WS78/110
    Manufacturer:
    NORTEK GLOBAL(REZNOR)
     
    WS-Series-Broc
    WS-Series-Install
    WS-Series-Spec

    Unit Heater Suspended Hydronic 110,000 (High) 78,000 (Low) Copper Tube/Alumimun Fins

  • Reznor Model WS Steam/Hot Water Suspended Heaters are design-engineered to be technically advanced and esthetically pleasing which makes it the hydronic heater for the 21st century.
    This smart new concept in commercial heating units will accommodate all architects who are looking for something new and different.
  • The heating range of Model WS is 13,000 to 350,000 BTUH. The air volume ranges from 270 to 4,750 CFM.
  • The heat exchanger is made of one or two rows of steel coils (standard or optional copper coils) with aluminum
  • The standard steel tubing is very strong and long lasting. Steel tubing is designed for hot water applications up to 150 psi.
  • The copper tubing used for the heating coil is very thick (0.03, 0.75 mm), making Reznor heating coils extremely sturdy and long lasting. The copper tube diameter is 0.867 (22 mm) O.D. The large tube diameter reduces the water pressure drop, which means these units require lower pump pressure than other hydronic heaters. It also allows a very rapid heat radiation. For steam heating applications copper tube (Option HA12) is required. Designed for high working steam pressure up to 145 psi (10 bar), every heat exchanger is subjected to a pressure test at over 350 psi (25 bar) before leaving the factory.
  • The heat exchanger assembly receives a special epoxy-polyester powder coating which makes the coil long lasting and increases the thermal output.
  • The Fan/Motor Assembly is made up of three components: the fan, the motor and the fan guard, which also acts as the main support for the fan. This fan guard is galvanized for protection against corrosion, and is mounted onto the main casing with anti-vibration rubber mountings. The fan guard meets OSHA requirements.*
  • The standard 2-speed motor is a hermetically sealed motor which is maintenance free. The motor is wired for Data Chart for fan RPM, heating output and CFM ranges. output, or low speed for reduced noise level. All motors have internal protection as a standard feature.
  • All Model WS units can be installed for either vertical or horizontal discharge.
  • pre-painted steel helps protect the cabinet against oxidation.
  • The cabinet is held together by shake-proof screws and molded corner sections to add additional strength and installation.
  • The optional Air Flow Induction Optimizer is available for horizontally discharged units. The Air Flow Induction the heated air stream. See the optional accessories section for more information.
  • Units are packaged into strong corrugated cardboard cartons with strengthened upper and lower side sections. These containers are clearly marked with the model number, size and approximate shipping weight.
  • Units are manufactured in an ISO 9001 registered facility.

    • Item#:
    WS78/110C
    Manufacturer Item:
    WS78/110C
    Manufacturer:
    NORTEK GLOBAL(REZNOR)
     
    WS-Series-Broc
    WS-Series-Install
    WS-Series-Spec

    Unit Heater Suspended Hydronic 33,000 (High) 23,000 (Low) Copper Tube/Alumimun Fins

  • Reznor Model WS Steam/Hot Water Suspended Heaters are design-engineered to be technically advanced and esthetically pleasing which makes it the hydronic heater for the 21st century.
    This smart new concept in commercial heating units will accommodate all architects who are looking for something new and different.
  • The heating range of Model WS is 13,000 to 350,000 BTUH. The air volume ranges from 270 to 4,750 CFM.
  • The heat exchanger is made of one or two rows of steel coils (standard or optional copper coils) with aluminum
  • The standard steel tubing is very strong and long lasting. Steel tubing is designed for hot water applications up to 150 psi.
  • The copper tubing used for the heating coil is very thick (0.03, 0.75 mm), making Reznor heating coils extremely sturdy and long lasting. The copper tube diameter is 0.867 (22 mm) O.D. The large tube diameter reduces the water pressure drop, which means these units require lower pump pressure than other hydronic heaters. It also allows a very rapid heat radiation. For steam heating applications copper tube (Option HA12) is required. Designed for high working steam pressure up to 145 psi (10 bar), every heat exchanger is subjected to a pressure test at over 350 psi (25 bar) before leaving the factory.
  • The heat exchanger assembly receives a special epoxy-polyester powder coating which makes the coil long lasting and increases the thermal output.
  • The Fan/Motor Assembly is made up of three components: the fan, the motor and the fan guard, which also acts as the main support for the fan. This fan guard is galvanized for protection against corrosion, and is mounted onto the main casing with anti-vibration rubber mountings. The fan guard meets OSHA requirements.*
  • The standard 2-speed motor is a hermetically sealed motor which is maintenance free. The motor is wired for Data Chart for fan RPM, heating output and CFM ranges. output, or low speed for reduced noise level. All motors have internal protection as a standard feature.
  • All Model WS units can be installed for either vertical or horizontal discharge.
  • pre-painted steel helps protect the cabinet against oxidation.
  • The cabinet is held together by shake-proof screws and molded corner sections to add additional strength and installation.
  • The optional Air Flow Induction Optimizer is available for horizontally discharged units. The Air Flow Induction the heated air stream. See the optional accessories section for more information.
  • Units are packaged into strong corrugated cardboard cartons with strengthened upper and lower side sections. These containers are clearly marked with the model number, size and approximate shipping weight.
  • Units are manufactured in an ISO 9001 registered facility.

    • Item#:
    WS23/33C
    Manufacturer Item:
    WS23/33C
    Manufacturer:
    NORTEK GLOBAL(REZNOR)
     
    WS-Series-Broc
    WS-Series-Install
    WS-Series-Spec
    |◀ ◀ 61 - 64 of 64 ▶ ▶|
    View: