S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
Uniweld PL15 Posi-Lock Replacement Gauge Lens 1.5"
Uniweld PL15
Test Products TPI395 Refractometer
Test Products TPI395
Item#:
TPI395
Manufacturer Item:
TPI395
Manufacturer:
TEST PRODUCTS INTERNATIONAL
Uniweld TGB30 Test Gauge 2" Diameter 30 psi Bottom Mounting
Uniweld TGB30
True-RMS measurements and optimized ergonomics make the 320 series clamp meters the best general troubleshooting tools for commercial and residential electricians. The 323, 324 and 325 are designed to verify the presence of load current, AC voltage and continuity of circuits, switches, fuses and contacts. These small and rugged clamp meters are ideally suited for current measurements up to 400 amp in tight cable compartments. The Fluke 324 model also includes temperature and capacitance measurement capabilities.
- True RMS AC voltage and current for accurate measurements on non linear signals
- Resistance measurement up to 4 kilo-ohm with continuity detection
- Temperature and capacitance measurement
- Slim, ergonomic design
- Large, easy to read backlight display
- Hold butTon
- 2 years warranty
- Soft carrying case
Fluke FLUKE-324
The Fluke TL175 TwistGuard test leads offer adjustable length test tips for use in different measurement environments. The TwistGuard adjustable tips enhance safety and versatility length. The WearGuard indicator shows damage to leads and provides heavy duty strain relief to withstand over 30000 bends.
- Patented TwistGuard extendable tip shroud meets the highest electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements
- New WearGuard lead wire wear indication; each test lead is covered by two layers of silicone insulation; inner contrasting color is exposed when the leads are nicked, scuffed or otherwise damaged and in need of replacement
- Double insulated silicone leads, TL175 test leads withstand high temperatures and remain flexible in cold temperatures
- Extra-heavy-duty strain relief on both probe-end and plug-end, tested beyond 30,000 bends without failure
- Universal input plugs are compatible with all instruments that accept standard 4 mm shrouded banana plugs
- Ratings - cat II 1000 volt, cat III 1000 volt, cat IV 600 volt, 10 amp maximum, pollution degree 2
- Includes removable 4 mm lantern tips that thread onto the lead tip
- Probes always show correct category rating for tip being used
- 1 year warranty
Fluke TL175
Item#:
TL175
Manufacturer Item:
TL175
Manufacturer:
FLUKE ELECTRONICS
Universal Enterprises DL589
Item#:
DL589
Manufacturer Item:
DL589
Manufacturer:
UNIVERSAL ENTERPRISES INC
Weiss Instruments E35-75BS Pressure Gauge Diameter 0-300 psi Bottom Mounting
Weiss Instruments E35-75BS
Item#:
E35-75BS
Manufacturer Item:
20300
Manufacturer:
WEISS INSTRUMENT INC
Uniweld G8-D Nitrogen Gauge 2" Diameter 0-600 psi Bottom Mounting
Uniweld G8-D
Fieldpiece Instruments ADLS2 Silicone Insulation Deluxe Test Lead, 3 feet Fieldpiece Instruments offers several test lead solutions specifically designed for the way HVAC technicians test in the field. Our detachable probe tip silicone test leads allow you to plug one probe tip directly into the top of our stick meter, attach an alligator clip extension tip onto the COM (common lead), and test with one hand, safely and easily. Add the red alligator extension to the volts lead to perform a"no-hands" test. We also offer spring loaded test lead kits, silicone test leads, shorting cables, and a flame diode adapter kit with mini-plug adapter. Just added to our test lead line is the RCT2 extended probe tip set that allows you to test connector plugs without dismantling the connector plug as well as hard to reach test points often found on tightly packed mini-split systems. It comes in the ADK7 deluxe silicone test lead kit.,
Fieldpiece Instruments ADLS2
Fieldpiece Instruments ADA2 Shorting Cable,
Fieldpiece Instruments ADA2
Fieldpiece Instruments offers several test lead solutions specifically designed for the way HVAC technicians test in the field. Our detachable probe tip silicone test leads allow you to plug one probe tip directly into the top of our stick meter, attach an alligator clip extension tip onto the COM (common lead), and test with one hand, safely and easily. Add the red alligator extension to the volts lead to perform a"no-hands" test. We also offer spring loaded test lead kits, silicone test leads, shorting cables, and a flame diode adapter kit with mini-plug adapter. Just added to our test lead line is the RCT2 extended probe tip set that allows you to test connector plugs without dismantling the connector plug as well as hard to reach test points often found on tightly packed mini-split systems. It comes in the ADK7 deluxe silicone test lead kit.
Fieldpiece Instruments ADK7
Fieldpiece Instruments ASP2 Static Pressure Probe for AMN2, ADMN2