• Uses rectification principle of electronic flame detection
• Primary control provides solid state, electronic flame safeguard protection for industrial and commercial single or dual fuel burners for rectification type flame detection
• Recycles if flame signal lost while in run, failure to establish pilot results in a lockout
• Safe-start check prevents start-up if flame-simulating failure occurs in flame detector circuit
• Includes built-in protection against ignition crossover in flame rod systems
• Solid state circuitry
• Mounts and removes easily through use of captive mounting screws
• Mounting base is made of strong thermoplastic
• Includes SPDT alarm contacts Honeywell Protectorelay RA890F1288 Flame Safeguard Primary Control, 120 VAC at 50/60 Hz, SPDTSid Harvey Item #:R202-52R: Replaces Part #:'s : 1C530R,
  ,
  
  

Sid Harvey Remanufactured R75-52R

• High limit opens burner circuit only.
• Includes transformer and accessory terminals for adding a remote low limit controller.
• Case available for horizontal or vertical mounting.
• Requires a 24 VAC thermostat with heat anticipator set at 0.2 amps.

• Immersion-type controllers that combine high limit protection with low limit and circulator control in forced hydronic heating systems
• Require 24 VAC thermostat with heat anticipator set at 0.2 amp (plus current draw of gas valve on L8124E)
• Include diaphragm powerhead and micro Switch assembly that respond to temperature changes in boiler water
• Mount directly to boiler
• Provide multi-zone control by using a separate circulator and R845 relay for each zone
• Electrical burner rating: full load - 7.4 amp at 120 VAC line voltage, 3.7 amp at 240 VAC; locked rotor - 44.4 amp at 120 VAC line voltage, 22.7 amp at 240 VAC
• Electrical circulator rating: 7.4 amp at 120 VAC, 3.7 amp at 240 VAC full load; 44.4 amp at 120 VAC, 22.2 amp at 240 VAC locked rotor

• Immersion type controllers that combine high limit protection with low limit and circulator control in forced hydronic heating systems
• Provide multi-zone control by using a separate circulator and R845 relay for each zone
• Include diaphragm powerhead and micro switch assembly that respond to temperature changes in boiler water
• Mount directly to boiler
• Select models include large transformers and extra terminals for supplying power to low voltage zone valves
• Require 24 VAC thermostat with heat anticipator set at 0.2 amp (plus current draw of gas valve on L8124E)

• Immersion type controllers that combine high limit protection with low limit and circulator control in forced hydronic heating systems
• Provide multi-zone control by using a separate circulator and R845 relay for each zone
• Include diaphragm powerhead and micro switch assembly that respond to temperature changes in boiler water Mount directly to boiler
• Select models include large transformers and extra terminals for supplying power to low voltage zone valves
• Require 24 VAC thermostat with heat anticipator set at 0.2 amp (plus current draw of gas valve on L8124E)

• Immersion type controllers that combine high limit protection with low limit and circulator control in forced hydronic heating systems
• Provide multi-zone control by using a separate circulator and R845 relay for each zone
• Include diaphragm powerhead and micro switch assembly that respond to temperature changes in boiler water
• Mount directly to boiler
• Select models include large transformers and extra terminals for supplying power to low voltage zone valves
• Require 24 VAC thermostat with heat anticipator set at 0.2 amp (plus current draw of gas valve on L8124E)

• Immersion type controllers that combine high limit protection with low limit and circulator control in forced hydronic heating systems
• Provide multi-zone control by using a separate circulator and R845 relay for each zone
• Include diaphragm powerhead and micro switch assembly that respond to temperature changes in boiler water
• Mount directly to boiler
• Select models include large transformers and extra terminals for supplying power to low voltage zone valves
• Require 24 VAC thermostat with heat anticipator set at 0.2 amp (plus current draw of gas valve on L8124E)