Diversitech HPR-3 1-Piece Heat Pump Riser
DiversiTech's Heat Pump Riser provides the desired elevation for condensers, heat pumps, and air handlers. The one-piece, heavy-duty plastic unit is manufactured in three heights. Butyl mastic on the top and bottom guarantees no slipping and reduced vibration and noise. Available in 1 or 2 piece risers. Four risers can handle up to 2,000 lb uniform load.,
,

HPR-3

HPR-3

Diversitech HP3232-8 Heat Pump Riser Pad 32" L x 32" W x 8" H for Use With Heat Pump Equipment
Provides an effective base for heat pump equipment installed in snowy climates. Rather than a combination of a typical 2" (or 3") equipment pad and 6in. Heat pump risers, the Heat Pump Pad provides a full 8" of elevation in a simple square footprint. The star pattern of the integral risers allows for installation of equipment with different size footprints up to 36 x 36". Also included are eight anti-vibration pads uniquely designed to fit into the guide slots on the top of the integral risers. The base is sloped outward to allow for easy drainage of condensate or defrost cycle condensate when the outdoor coil is operating in heat pump mode. Nestable for efficient shipping, transportation, and warehousing. Injection molded from concrete gray, recycled polypropylene material, the Heat Pump Pad is environmentally friendly and designed to last longer than the equipment it supports. US Patent Number 7,891,635, and other patent(s) pending.

,
,

HP3232-8

HP3232-8

Diversitech UC2448-3 Ultralite Equipment Pad 48" x 24" x 3" H Fiber Reinforced Cement Pad

UC2448-3

UC2448-3

Diversitech UC3040-3 Ultralite Equipment Pad

• 30" x 40" x 3" H Fiber Reinforced Cement Pad
  Product
• Extremely lightweight, the UltraLite pad is a concrete pad at the weight of plastic, about 2.5 lbs. per square foot
• Concrete outer skin and EPS foam core provide flexibility and vibration dampening
• Flat bottom design provides excellent resistance to sinking and settling
• The textured surface of the UltraLite prevents equipment sliding and allows water drainage
• Extensive selection of sizes available including wedge-shaped pad
• Drillable for securing unit (¼ x 1-¼" Tapcon recommended), either side or top surface
• Freeze/thaw, UV, chemical & flame-resistant for long-term life outdoors
• Tested per ASTM D2299 with refrigerants, synthetic canine urine, compressor oil or salt solution
• Resistant to heating caused by the compressor and the surface is resistant to heat from incidental torch flame during installation,
  ,
  
  
  
  

  UC3040-3

  
  

  UC3040-3

Diversitech UC2442-3 Ultralite Equipment Pad

• 42" x 24" x 3" H Fiber Reinforced Cement Pad
  Product
• Extremely lightweight, the UltraLite pad is a concrete pad at the weight of plastic, about 2.5 lbs. per square foot
• Concrete outer skin and EPS foam core provide flexibility and vibration dampening
• Flat bottom design provides excellent resistance to sinking and settling
• The textured surface of the UltraLite prevents equipment sliding and allows water drainage
• Extensive selection of sizes available including wedge-shaped pad
• Drillable for securing unit (¼ x 1-¼" Tapcon recommended), either side or top surface
• Freeze/thaw, UV, chemical & flame-resistant for long-term life outdoors
• Tested per ASTM D2299 with refrigerants, synthetic canine urine, compressor oil or salt solution
• Resistant to heating caused by the compressor and the surface is resistant to heat from incidental torch flame during installation,
  ,
  
  
  
  

  UC2442-3

  
  

  UC2442-3

Diversitech UC1636-3 Ultralite Equipment Pad

• 36" x 16" x 3"H Fiber Reinforced Cement Pad
  Product
• Extremely lightweight, the UltraLite pad is a concrete pad at the weight of plastic, about 2.5 lbs. per square foot
• Concrete outer skin and EPS foam core provide flexibility and vibration dampening
• Flat bottom design provides excellent resistance to sinking and settling
• The textured surface of the UltraLite prevents equipment sliding and allows water drainage
• Extensive selection of sizes available including wedge-shaped pad
• Drillable for securing unit (¼ x 1-¼" Tapcon recommended), either side or top surface
• Freeze/thaw, UV, chemical & flame-resistant for long-term life outdoors
• Tested per ASTM D2299 with refrigerants, synthetic canine urine, compressor oil or salt solution
• Resistant to heating caused by the compressor and the surface is resistant to heat from incidental torch flame during installation,
  ,
  
  
  
  

  UC1636-3

  
  

  UC1636-3

ltraLite is a true concrete equipment pad at the weight of plastic (about 2.5 lbs. per square foot). UltraLite is strengthened by miles of fiber in each square foot of fiber-cement coating. This fiber allows the pad to flex instead of cracking or breaking. The textured surface prevents the condensing unit or portable generator from sliding, and allows water drainage, while the engineered encapsulated polystyrene (EPS) core prevents warping and provides a solid bottom to resist settling. UltraLite is unaffected by soil conditions, ultraviolet (UV) light, temperature extremes, and other weather conditions.
DiversiTech SpeediChannel is an innovative channel system used to cover air conditioning line sets. The two part system has a base and a cover. The base is fastened to a wall or ceiling, then a clever little plastic clip (SpeediClip) snaps into a channel already molded into the base. Then, using standard cable ties, the line set, cables, control wires, and/or condensate drain line are fastened in place. The cover then snaps simply on top of the base. Manufactured from rigid PVC, the SpeediChannel system is a natural color that is a very close match to the typical mini-split condensing unit case. However, the Speedi-Channel system can be painted as desired to match any wall color. The PVC used in the SpeediChannel system is resistant to UV light, and is UL rated.

UC1636-2

UC1636-2

Diversitech U3353-3 Ultralite Equipment Pad 33" x 53" x 3 " H Fiber Reinforced Cement Pad
,

U3353-3

U3353-3

The Diversitech, Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is resistant to impact, ultra violet degradation and weathering and will not crack, flake, or warp. The Hef-T-Pad is virtually impervious to climatic variations. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.
,

X2424211

X2424211

The Diversitech, Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is resistant to impact, ultra violet degradation and weathering and will not crack, flake, or warp. The Hef-T-Pad is virtually impervious to climatic variations. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.

X2436211

X2436211

The Diversitech, Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is resistant to impact, ultra violet degradation and weathering and will not crack, flake, or warp. The Hef-T-Pad is virtually impervious to climatic variations. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.

X3636311

X3636311

The Diversitech, Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is resistant to impact, ultra violet degradation and weathering and will not crack, flake, or warp. The Hef-T-Pad is virtually impervious to climatic variations. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.

X3030211

X3030211