• The maxivent features a low profile, fit anywhere solid brass body and cover and a high temperature polypropylene float
• Angle body pattern

Honeywell FV147

• Solid state plug-in amplifiers that respond to flame detector inputs to indicate the presence of flame when used with 7800 series relay modules
• Flame failure response time of 2 or 3 sec
• Flame signal strength ranges from 0 - 5 VDC
• Plug into 7800 relay module through printed circuit board edge connector keyed for proper orientation
• Flame signal test jacks to measure amplifier flame signal voltage
• Color coded labels identify flame detection type
• Dynamic self-check amplifier test the detectors and all electronic components in the flame detection system 7800 series relay module locks out on safety shutdown with flame detection system failure
• Compatible with existing Honeywell flame detectors
• Use with flame sensor gas rectifying flame rods C7004, C7005, C7007, C7008, C7009, Q179; gas, oil, coal ultraviolet flame sensor C7012A, C

honeywell r7847a1033

• Immersion-type controllers that combine high limit protection with low limit and circulator control in forced hydronic heating systems, including domestic hot water service
• Require 24 VAC thermostat with heat anticipator set at 0.2 amp (plus current draw of gas valve on L8124E)
• Include diaphragm powerhead and micro Switch assembly that respond to temperature changes in boiler water
• Mount directly to boiler
• Provide multi-zone control by using a separate circulator and R845 relay for each zone
• Electrical burner rating: at full load: 7.4 amp at 120 VAC, 3.7 amp at 240 VAC line voltage; at locked rotor: 44.4 amp at 120 VAC, 22.7 amp at 240 VAC line voltage
• Electrical circulator rating: 7.4 amp at 120 VAC, 3.7 amp at 240 VAC full load; 44.4 amp at 120 VAC, 22.2 amp at 240 VAC locked rotor
• 1-1/2" depth insulation

Honeywell C317-5

• Totally enclosed micro switch snap-acting switches operate on temperature rise to setpoint
• Visible control point scale and external adjustments screw permit easy setting
• Direct or well immersion of the sensing element
• Remote bulb model may be used to sense air temperature in ducts and in outside air sensing applications Honeywell L4006A2007 High or Low Limit Immersion Aquastat Controller, 100 - 240 deg F, 5 - 30 deg F DifferentialSid Harvey Item #:C290A: Replaces Part #:'s : AQU4006A1678-C290 | AQU4006A2007-C290A | C290 | C290R |,
  ,
  
  
  

  Honeywell C290A

• Totally enclosed micro switch snap acting switches operate on temperature rise to setpoint
• Visible control point scale and external adjustments screw permit easy setting
• Horizontal insertion of the sensing element
• Direct/well immersion of the sensing element
• Remote bulb model may be used to sense air temperature in ducts and in outside air sensing applications
• Contacts make on temperature rise
• Screw terminals wiring

• Totally enclosed micro switch snap-acting switches operate on temperature rise to setpoint
• Visible control point scale and external adjustments screw permit easy setting
• Horizontal or vertical insertion of the sensing element
• Remote bulb model may be used to sense air temperature in ducts and in outside air sensing applications
• Direct or well immersion of the sensing element
• Includes heat-conductive compound, well adapter Honeywell L4006E1067 High Limit Manual Reset Aquastat, 130 - 270 deg F, 10 - 25 deg F DifferentialSid Harvey Item #:C290-6: Replaces Part #:'s : L39-029,
  
  ,
  
  
  

  Honeywell C290-6

• Totally enclosed micro switch snap acting switches operate on temperature rise to setpoint
• Visible control point scale and external adjustments screw permit easy setting
• Horizontal or vertical insertion of the sensing element
• Direct/well immersion of the sensing element
• Remote bulb model may be used to sense air temperature in ducts and in outside air sensing applications
• Contacts break on temperature rise
• Screw terminals wiring

Honeywell C290-6A

Honeywell C312-8