S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
2.50 GPH 2.50-45B-HAGO
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
2.50 gph 2.50-45ss-hago
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
2.50 GPH 2.50-60SS-HAGO
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
2.75 GPH 2.75-45P-HAGO
Item#:
2.75-45P-HAGO
Manufacturer Item:
030G6338
Manufacturer:
DANFOSS LLC
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
Item#:
3.00-45SS-HAGO
Manufacturer Item:
030G6640
Manufacturer:
DANFOSS LLC
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
3.00 gph 3.00-60h-hago
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle