Nu-Calgon 4297-75 Pipe-Dri is an aerosol insulation which provides a moisture barrier to stop sweating and dripping on refrigeration lines, air conditioning lines, and other cold surfaces. Quickly adheres and dries to a hard water proof coating. Pipe-Dri's spray pattern permits spraying of odd shaped fittings and makes it possible to insulate hard to reach areas. Sweating and dripping are eliminated by this durable, waterproof protective barrier. It separates the warm moist air and the cold surface, preventing condensation from occurring. Pipe-Dri offers the ability to apply on odd shaped fittings and hard to reach areas. Reapplication will continue to build thickness as required. One can will normally cover approximately ten feet of 1" water pipe or eight square feet of flat surface area with two coats. Ideally, the product should be at room temperature (70- 75 deg F) and the surface to be coated at a lower temperature. A thick application is hard to form on warmer surfaces (above 80 deg F), however, a thicker coat may be achieved by applying 2 or more light coats. Once a coating has been allowed to dry and harden, it will be stable at temperatures up to 120 deg F.

Nu-Calgon 4774-0 For spraying coil cleaners such as Nu-Brite, CalClean, HD CalClean, Alka-Brite Plus, Tri-Pow'r HD or any of the other quality Nu-Calgon coil cleaners for cleaning air cooled condensers, evaporator coils, etc. No pre-mixing is necessary as chemical and water are automatically blended in mixing head as you spray. Use for coil cleaning as well as in food preparation areas, wash rooms, or any situation where use of water-diluted chemicals are required.

• The coil gun probe provides easy access for inside out cleaning of coils
• Recommended water pressure 40 - 60 psi
• Quick-disconnect feature
• Foam wand to enhance foaming
• Deflector tip to fan out spray
• Connects to optional coil gun probe accessory (4774-1) for 90 deg direction of spray inside the coil

Sid Harvey Item #:4774-0: Replaces Part #:'s : 4814,

,

Nu-Calgon 9534-40 Prefilter Cartridge EC110 10",
,

Nu-Calgon 9534-20 Prefilter Cartridge EC210,
,

Nu-Calgon 9534-20

Nu-Calgon 9795-80 Pre-Filter Housing W/Cartridge E-10,
,

Nu-Calgon 9795-80

Nu-Calgon 9795-90 Pre-Filter Housing W/Cartridge E-20,
,

Nu-Calgon 4299-T8 Pump Protector, 10 oz Spray Can, Colorless Foam-in shut down corrosion protection for all types of pumps any pump that is shut down and drained part of the time should be safeguarded with aerosol pump protector. Pumps used in cooling towers, swimming pools and vacation homes, auxiliary pumps, marine and industrial pumps can develop corrosion deposits on the impeller and other close-tolerance areas during shut down, causing the pump to bind. Aerosol pump protector prevents this corrosion and lubricates the pump so that it starts right up every time! pump protector is water soluble and will not cause any foaming problem when the pump is started. If the pump is used for drinking water, flush it thoroughly by running water off a few minutes before placing the pump back in service. Protects seasonally operated pumps against corrosion during shutdowns by"winterizing" them. When corrosion occurs in close-tolerance areas, it can cause the impeller to stick or bind. Protect your clients investment and your reputation! Safe for all types of water pumps and it requires no special rinsing at start-up.

• Protects against corrosion and ends-pump impeller binding
• Convenient aerosol package
• Safe for all types of water pumps
• One can is enough for most pumps
• Requires no special rinsing at startup
• Protects pool pumps throughout the winter
• This product has been authorized by the USDA for use in federally inspected meat and poultry plants
• 95% volatile
• Level 1 heat of combustion
• 13 cm flame height, 4 - 5 sec flammability duration Foam-in shut down corrosion protection for all types of pumps any pump that is shut down and drained part of the time should be safeguarded with aerosol pump protector. Pumps used in cooling towers, swimming pools and vacation homes, auxiliary pumps, marine and industrial pumps can develop corrosion deposits on the impeller and other close-tolerance areas during shut down, causing the pump to bind. Aerosol pump protector prevents this corrosion and lubricates the pump so that it starts right up every time! pump protector is water soluble and will not cause any foaming problem when the pump is started. If the pump is used for drinking water, flush it thoroughly by running water off a few minutes before placing the pump back in service. Protects seasonally operated pumps against corrosion during shutdowns by"winterizing" them. When corrosion occurs in close-tolerance areas, it can cause the impeller to stick or bind. Protect your clients investment and your reputation! Safe for all types of water pumps and it requires no special rinsing at start-up.,
  ,
  
  
  

  Nu-Calgon 4299-T8

Nu-Calgon 1903D PurCool strips are powerful, economical, preventive maintenance for A/C condensate drain pans. Just place them anywhere in the drain pan where the PurCool strips will contact the condensate water and enjoy up to six months of economical protection. PurCool strips will adhere to the drain pan and will not float or move. They dissolve completely, leaving no residue. Safe for metal and plastic drain pans.

Nu-Calgon 1903D

Nu-Calgon PCG10T Purcool Green Strips 10 Ton,
,

Nu-Calgon 4050-15 UV Leak Detection Kit for 4050-11, 4050-12 EasySeal,
,

Nu-Calgon 4050-15

Nu-Calgon 4050-01 A/C EasySeal is designed to prevent as well as repair leaks anywhere in the system, including condensers, evaporators, copper lines, and soldered joints. It is easily injected into the system, traveling with the refrigerant, searching for leaks. The fact that A/C EasySeal travels with the refrigerant is very important to its ability to find leaks faster, using less sealant than those sealants designed to mix and travel with the systems oil. The A/C EasySeal circulates through the system with the refrigerant seeking out leaks rather than migrating slowly with the oil keeping in mind that only a small portion of the system oil actually migrates with the refrigerant through the system. A/C EasySeal will react with moisture or air that is naturally present at a leak, forming a secure seal. A/C EasySeal is compatible with the refrigerant, oil and all system materials and it will not react until it comes into contact with the air and moisture at the leak, forming a permanent seal. A/C EasySeal is a time saver. It finds leaks quickly and seals them, saving the time and money required in searching for the smallest leaks. With A/C EasySeal, the contractor is able to just add a can to the system and be confident the leak has been fixed and move on to the next job.

• Treats fractional to 1.5 Ton
• Prevents refrigerant leaks and seals existing leaks in air conditioning and refrigeration systems permanently
• Eliminates expensive leak search and repair
• Travels with refrigerant to find leaks fast
• Utilizes a reusable hose

,
,